Top 10 typical forklift crashes ， forklift procedure need to pay attention to these issues ！.

Do not undervalue the forklift at the office. If the procedure is bad, there will certainly be severe accidents in minutes, and there are many mishaps involving forklifts.

Case 1: The forklift cargo obstructed the driver's view, and the individual ahead could not be discovered, resulting in a rolling accident.
Case 2: In order to preserve the equilibrium of the forklift when lifting heavy items, the staff members utilized their body weight as the weight, which practically triggered casualties.
Instance 3: The size of the forklift cargo goes beyond the allowable width of the course and hangs on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over throughout a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not notice the forklift.
Situation 6: The forklift raises the employees illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the chauffeur is squashed when the forklift surrender.
Instance 7: The forklift chauffeur did not wear a seat belt and fell from the lorry when it rolled over and was squashed.
Forklift procedure need to take notice of these matters ：.

Begin.
1. Prior to beginning, observe the surroundings, and after verifying that there are no challenges that impede the safety and security of driving, honk the horn first and after that start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress (air pressure) gauge need to be risk-free prior to starting.
3. When the forklift begins with a tons, the driver needs to initially confirm that the tons is steady and trusted.
4. The begin should be slow-moving and steady.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be slanted in reverse. .
2. Do not raise the fork too expensive when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork must be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be released initially. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is forbidden to brake instantly while driving with tons unless there are unique situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be increased except when stacking or packing. .
8. The height of the load must not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and Stand-on Electric Pallet Stacker one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked Electric Forklift Truck for Warehouse with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the tons, and it must be kept in mind that the fork pointer ought to not touch various other goods or items. The lots ought to be supported with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be tilted ahead somewhat when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or depress the parking brake switch.
3. The engine is turned off and the power is removed. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Examine the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, examine whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you run into somebody in front of you during driving, you must send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of " totally free switching";.
6. Running up and down the slope must be slow and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844